Cisco SFP-10G-SR= SFP-10G-SR Network Media Converter

Product Information

provides network connectivity when there are software or hardware failures. Hardware bypass is useful on ports where the Firepower The serial number for the Firepower 2100 series chassis is located on the pullout asset card on the front panel. Figure 7. Serial Number on the Chassis

The Cisco 10GBASE Dense Wavelength-Division Multiplexing SFP+ Module offer the following features and benefits: Note: Parameters are specified over temperature and at end of life unless otherwise noted. When shorter distances of single-mode fiber are used (<40km), an inline optical attenuator must be used to avoid overloading and damaging the receiver. flow control, and does not support a remote dial-in modem. The baud rate is 9600. You can use the standard cable found in The Cisco SFP-10G-SR is in full compliance with the 10G BASE-SR standard. This module has a link length of 26m on the most commonly used standard FDDI- grade multimode fiber. FDDI stands for Fiber Distributed Data Interface. It supports a link length of 300m over OM3 cables and a link length of 400m over OM4 cables. A hardware classification engine provides support for advanced data center requirements, including stateless network offloads for VXLAN, NVGRE, and GENEVE. Additional features support low-latency kernel bypass for performance optimization through usNIC, DPDK, SR-IOV and server virtualization support using NetQueue and VMQ/VMMQ. The Cisco UCS VIC 15000 Series provide high network performance and low latency for the most demanding applications:Dimensions (H x W x D): 8.5 x 13.4 x 56.5mm. Cisco SFP+ connectors typically weigh 75 grams or less. Cisco has introduced that the S-class modules are suggested to be used in enterprise network. In addition, the operating temperature range is smaller, thus, S-class module is recommended for shorter transmission distance applications compared with other standard modules. The Firepower 2130 and 2140 contain one network module slot that provides optical or electrical network interfaces. Network

A SFP-10G-BXD-I device is always connected to a SFP-10G-BXU-I device with a single strand of standard SMF with an operating transmission range up to 10 km. Visit https://www.cisco.com/c/en/us/products/collateral/interfaces-modules/dwdm-transceiver-modules/data_sheet_c78-711186.html. Extended warranty (optional): Cisco SFP+ modules can be covered in a Cisco SMARTnet® Service support contract for the Cisco switch or router chassis Hot-swappable input/output device that plugs into an Ethernet SFP+ port of a Cisco switch (no need to power down if installing or replacing) Hardware bypass is supported only on a fixed set of ports. You can pair Port 1 with Port 2, Port 3 with Port 4, but you cannotYou cannot swap SSDs between different Firepower platforms. For example, you cannot use a 4100 series SSD in a 2100 series See Remove and Replace the Power Supply Module for the procedure for removing and replacing the power supply module in the Firepower 2130 and 2140. The fan LED is located on the front of the chassis. See Product ID Numbers for a list of the PIDs associated with the 2100 series fans. You can fit four copper SFPs in either the top row of ports or the bottom row of ports. Both rows cannot be populated at the The following figure shows the front panel of the Firepower 2130 and 2140. See Front Panel LEDs for a description of the LEDs.

The Cisco 10GBASE-ER Module supports a link length of up to 40 kilometers on standard Single-Mode Fiber (SMF, G.652).

The Cisco 10GBASE-LRM Module also supports link lengths of 300m on standard Single-Mode Fiber (SMF, G.652). The GLC-GE-DR-LX SFP can interoperate with other 1G SFPs/interfaces as long as those are based on 1000BASE-LX/LH standard. No attenuator is needed in any fiber strand. module and the 12-V main power is OFF. When the switch is in the ON position, the 12-V main power is turned on and the system