Joined in 2023 
82 
63 About this deal
RJ45/RJ11 Network Cable Splitters for Ethernet and Phone Line Sharing". carry one old fashioned analog telephone signal and one 10/100Mbps Ethernet signal by the same single network cable. Ethernet Cable Identification and Use". Donutey. Archived from the original on 2011-07-10 . Retrieved 2011-04-01.
Cat5e is capable of upto gigabit networking speeds (this is dependent on your network). Our cat5e cables are flexible and easy to install. Cat5 cable is designed to carry data over a wired network connection at speeds of 10 Mbps (Ethernet) or 100 Mbps (Fast Ethernet). You will often see this written as 10/100 Ethernet when shopping for Cat5 cable online. This means that if your local network or incoming internet connection runs at between 10-100 Mbps (also known as a 100BASE-T network), Cat5 Ethernet cable should be able to handle the required data throughput at full speed, with no loss or delay. Selecting coax and twisted-pair cable". Electronic Products. Archived from the original on 2009-02-01. The Category5e specification improves upon the Category5 specification by further mitigating crosstalk. [9] The bandwidth (100MHz) and physical construction are the same between the two, [10] and most Cat 5 cables actually happen to meet Cat 5e specifications even though they are not certified as such. [11] Category5 was deprecated in 2001 and superseded by the Category5e specification. [12]U/UTP is, therefore, the most susceptible to interference, signal noise, return loss, and attenuation, although the cable will be considerably cheaper to buy. F/FTP will offer the greatest protection against performance-limiting factors like crosstalk, but it will also be the most expensive type to buy.
The maximum length for a cable segment is 100 meters (330ft) per TIA/EIA 568-5-A. [31] If longer runs are required, the use of active hardware such as a repeater or switch is necessary. [32] [33] The specifications for 10BASE-T networking specify a 100-meter length between active devices. [34] This allows for 90 meters of solid-core permanent wiring, two connectors and two stranded patch cables of 5 meters, one at each end. [35] Conductors [ edit ] Shielded cables ( FTP or STP) are useful for environments where proximity to RF equipment may introduce electromagnetic interference, and can also be used where eavesdropping likelihood should be minimized. Understanding Cat - 5 Cables" (PDF). Satelliete & Cable TV. Archived from the original (PDF) on 2013-05-15 . Retrieved 2013-01-05. For home users, a CAT5e cable should be sufficient for all your networking needs. However, if you’re setting up a commercial network CAT6 cabling is a must. It is faster, more efficient, and will result is less network downtime due to its superior quality. Cat5 Spec, cat6 specs, cat7 spec - Definitions, Comparison, Specifications". TEC Datawire. Archived from the original on 2013-07-19 . Retrieved 2013-01-05.
U/UTP (Unshielded/Unshielded Twisted Pair): Neither the individual twisted pairs nor the cable has any additional shielding built-in. Only the basic protections - the standard insulation around each twisted wire, and the cable sheath itself - are present
The distance per twist is commonly referred to as pitch. Each of the four pairs in a Cat5 cable has differing pitch to minimize crosstalk between the pairs. The pitch of the twisted pairs is not specified in the standard. Outer insulation is typically polyvinyl chloride (PVC) [27] or low smoke zero halogen (LS0H). [ citation needed] Example materials used as insulation in the cable [28] AcronymCat 5E cables are most commonly utilized with unshielded twisted pairs (UTP). However, environments with large motors, generators, and certain types of high-voltage lighting are major sources of Electromagnetic and Radio Frequency Interference (EMI/RFI). In these applications, shielded twisted pair (STP) cable will help protect data signals when connected properly.
Additional Transmission Performance Guidelines for 4-pair 100v category5 Cabling" (PDF). Archived from the original (PDF) on 2013-10-05 . Retrieved 2013-05-12. In basic construction terms, there are two main types of Cat5 and Cat5e cable, namely stranded core and solid core. These terms refer to how the data-carrying wires, or conductors, that make up the inner core of the cable are arranged. It has been suggested that this section should be split into a new article titled Twisted pair, because Applies not only Cat 5, but to all communication cabling. ( discuss) ( June 2023) See to the right for a Cat5e cable diagram, showing the basic construction of different types of Cat5e Ethernet cables.
Cat5 cable specifications dictate it should be able to handle data transfer over Ethernet networks at frequencies (also known as bandwidth, or data-carrying capacity) of up to 100 MHz. Cat5e offers superior performance and is rated for frequencies of up to 350 MHz. This is due in part to its stricter performance requirements for things like crosstalk (interference between individual wires), attenuation and return loss. Cat5 is also used to carry other signals such as telephony and video. [17] In some cases, multiple signals can be carried on a single cable; Cat5 can carry two conventional telephone lines as well as 100BASE-TX in a single cable. [18] [19] [20] [21] [22] The USOC/RJ-61 wiring standard may be used in multi-line telephone connections. Various schemes exist for transporting both analog and digital video over the cable. HDBaseT (10.2 Gbit/s) is one such scheme. [23] Characteristics [ edit ] At first glance, you cannot necessarily tell whether a given length of Ethernet cable is stranded or solid without cutting through it to find out. However, stranded cable is usually a lot more flexible than solid core cable. Solid cables will often retain some degree of deflection for a while after being bent at a sharp angle. Cat5e Cable Diagram
Great Deal 
New Comment